Materials Transactions Online

Materials Transactions, Vol.59 No.06 (2018) pp.969-975
© 2018 The Japan Institute of Metals and Materials

Brazed Bonding between SiAlON and Heat-Resistant Alloys with Application of Filler Materials

Toko Tokunaga1, Masayuki Koshiyama2, Kazuya Kurokawa1, Munekazu Ohno1 and Kiyotaka Matsuura1

1Faculty of Engineering, Hokkaido University, Sapporo 060-8628, Japan
2Graduate School of Engineering, Hokkaido University, Sapporo 060-8628, Japan

It has been required to improve the heat efficiency of thermal power generation system for the sake of mitigation of the global warming and resource depletion problems. For improving the heat efficiency, it is effective to increase the steam temperature, and as a result, appropriate heat-resistant alloys are needed. Although SUS304 stainless steel and Ni-based superalloys have been proposed as promising heat-resistant alloys until now, there still remain some concerns such as high-temperature corrosion by flaming gas and erosion by combustion ash. Thus, the present authors propose SiAlON ceramic coating on SUS304 and INCONEL X-750 because SiAlON has excellent heat, wear and corrosion resistances. In the present study, brazed bonding between SiAlON and these heat-resistant alloys was attempted with the applications of Cu and Ag as a soft filler material to reduce the residual stress generated due to the difference in thermal expansion coefficient between SiAlON and the heat-resistant alloys. As for the bonding with the Cu filler, the SiAlON/Cu/SUS joint was successful when the brazing time was short. However, when the brazing time was long (for example, 60 minutes), Fe-based grains were formed in the Cu filler layer, and the cracks were formed in the SiAlON near the joint interface during cooling in the brazing process. It was considered that the Cu filler was hardened by the formation of the Fe-based grains and could not reduce the residual stress. As for the bonding with the Ag filler, on the other hand, the SiAlON/Ag/SUS joint was successful even for a long brazing time. The SiAlON/Ag/INCONEL joint was also successful. The bending strengths of these SiAlON/Cu/SUS, SiAlON/Ag/SUS and SiAlON/Ag/INCONEL joints were evaluated by a three point bending test, and the results were approximately 200, 270 and 350 MPa, respectively. In all cases fracture occurred in the SiAlON, which means that the SiAlON and the alloys were strongly bonded.

[doi:10.2320/matertrans.M2018038]

(Received 2018/01/31; Accepted 2018/03/15; Published 2018/05/25)

Keywords: ceramic coating, SiAlON, bonding, filler, stainless steel, Ni-based alloy, brazing

PDF(member)PDF (member) PDF(organization)PDF (organization) Order DocumentOrder Document Table of ContentsTable of Contents

REFERENCES

  1. Fukuda M.: J. Japan Weld. Soc. 82 (2013) 472-476.
  2. Fukaya Y., Okumoto Y., Ikuta A., Kuroki H., Shinozaki K. and Kobayashi T.: Quarterly J. Japan Weld. Soc. 19 (2001) 336-344.
  3. Ferreño D., Gorrochategui I., Sánchez L. and Gutiérrez-Solana F.: Eng. Fail. Anal. 11 (2004) 799-810.
  4. Nakamura H., Umebayashi S. and Kishi K.: J. Ceram. Soc. Japan 97 (1989) 1412-1415.
  5. Kohno A., Yamada T. and Yokoi K.: J. Japan Inst. Met. Mater. 49 (1985) 876-883.
  6. Koshiyama M., Sako H., Ohno M. and Matsuura K.: J. Japan Inst. Met. Mater. 79 (2015) 191-194.
  7. Lee W.C.: J. Mater. Sci. 32 (1997) 6657-6660.
  8. Wang N.: Ceram. Int. 42 (2016) 12815-12824.


[JIM HOME] [JOURNAL ARCHIVES]

© 2018 The Japan Institute of Metals and Materials
Comments to us : editjt@jim.or.jp