Materials Transactions Online

Materials Transactions, Vol.58 No.02 (2017) pp.164-166
© 2016 The Japan Institute of Metals and Materials

Effect of Shot Peening on Residual Stress and Microstructure in the Deformed Layer of Inconel 625

L.H. Wu1 and C.H. Jiang1

1School of Materials Science and Engineering, Shanghai Jiao Tong University, 800 Dongchuan Road, Shanghai 200240, PR China

Effect of shot peening on residual stress and microstructure in the deformed layer of Inconel 625 was investigated. Residual stress and microstructure including the domain size, micro strain and dislocation density was characterized by X-Ray diffraction method (XRD). The results showed that shot peening (SP) can significantly improve the compressive residual stress and micro hardness. Moreover, microstructure evaluation revealed that smaller domains were refined and the higher micro strain was induced by shot peening process. Thus a high dislocation density in the near-surface of the deformed layers was induced. Dual shot peening process could optimize the distribution of both compressive residual stress and the microstructure, which will help with the material fatigue and corrosion resistance.

[doi:10.2320/matertrans.M2016298]

(Received 2016/08/29; Accepted 2016/11/25; Published 2017/01/25)

Keywords: Inconel 625, residual stress, microstructure, shot peening, X-Ray diffraction (XRD)

PDF(member)PDF (member) PDF(organization)PDF (organization) Order DocumentOrder Document Table of ContentsTable of Contents

REFERENCES

  1. B.X. Feng, X.N. Mao, G.J. Yang, L.L. Yu and X.D. Wu: Mater. Sci. Eng. A 512 (2009) 105-108.
  2. Q. Feng, C.H. Jiang and Z. Xu: Mater. Des. 47 (2013) 68-73.
  3. W.Z. Luan, C.H. Jiang and V. Ji: Mater. Trans. 50 (2009) 837-840.
  4. W.Z. Luan, C.H. Jiang and V. Ji: Mater. Trans. 50 (2009) 1499-1501.
  5. J.W. Tian, K. Dai, J.C. Villegas, L. Shaw, D.L. Klarstrom and A.L. Ortiz: Mater. Sci. Eng. A 2 493 (2008)176-183.
  6. T.M. Pollock and S. Tim: J. Propul. Power 22 (2006) 361-374.
  7. I.C. Noyan, J.B. Cohen: Springer-Verlag. New York (2009) 120-126.
  8. Z. Wang and C. Jiang: Appl. Surf. Sci. 257 (2010) 1154-1160.
  9. G.K. Williamson and R.E. Smallman: Philos. Mag. 1 (1956) 34-36.
  10. T. Ungár: Mater. Sci. Eng. A 309-310 (2001) 14-22.
  11. T. Ungár: Scr. Mater. 51 (2004) 777-781.
  12. Y.K. Gao, M. Yao and J.K. Li: Metallurgical and Materials Transactions a-Physical Metallurgy and Materials Science 33 (2002) 1775-1778.
  13. S. Wang, Y. Li and M. Yao: J. Mater. Process. Technol. 73 (1998) 64-73.
  14. M.A. Meyers, A. Mishra and D.J. Benson: Prog. Mater. Sci. 51 (2006) 550-556.
  15. R.S. Liu and J.Y. Li: Mater. Sci. Eng. A 114 (1989) 127-132.


[JIM HOME] [JOURNAL ARCHIVES]

© 2016 The Japan Institute of Metals and Materials
Comments to us : editjt@jim.or.jp