Materials Transactions Online

Materials Transactions, Vol.52 No.5 (2011)

817-817 :
PREFACE
Yoshimasa Takayama, Toshiya Shibayanagi, Kenji Matsuda, Takayuki Tsuchida, Shinji Kumai, Osamu Umezawa and Tatsuo Sato
818-824 :
Aluminium in Innovative Light-Weight Car Design
Jürgen Hirsch
825-829 :
Change in Crystal Orientations of a {100} < 001> Pure Aluminum Single Crystal during Accumulative Roll Bonding
K. Kashihara, W. Ikushima, Y. Miyajima, D. Terada and N. Tsuji
830-833 :
Refinement Factors of Mechanical Vibrations on Microstructure of Al-7 mass% Si Alloys
Takuya Tamura, Toshiro Matsuki and Kenji Miwa
834-841 :
Semi-Solid Microstructure Control of Wrought Al-Mg-Si Based Alloys with Fe and Mn Additions in Deformation-Semi-Solid-Forming Process
Chakkrist Phongphisutthinan, Hiroyasu Tezuka and Tatsuo Sato
842-847 :
Grain Morphology of As-Cast Wrought Aluminium Alloys
Mark Easton, Cameron Davidson and David StJohn
848-855 :
Effects of High-Temperature Solutionizing on Microstructure and Tear Toughness of A356 Cast Aluminum Alloy
Yohei Harada, Shinichi Tamura and Shinji Kumai
856-861 :
Effect of Si Content on Strip Thickness and Solidified Structure in High-Speed Twin-Roll Cast Al-Si Alloy Strips
Min-Seok Kim and Shinji Kumai
862-867 :
Statistical Analysis for Influence of Factors on Morphological Evolution in Semi-Solid Al-6Zn-2.5Mg-0.5Cu Alloy by Cooling Plate Method
Sung-Yong Shim, Dae-Hwan Kim, Young-Rok Seong and Su-Gun Lim
868-875 :
Experimental Observation of Elasto-Plasticity Behavior of Type 5000 and 6000 Aluminum Alloy Sheets
Shohei Tamura, Satoshi Sumikawa, Takeshi Uemori, Hiroshi Hamasaki and Fusahito Yoshida
876-881 :
Changes in Microstructures during Annealing after Cold-Rolling at 30% and 50% Reduction on Al-Mg-Si Alloy
Atsushi Yamamoto, Masaaki Tsukamoto and Daisuke Okai
882-889 :
Development of Ultra-Fine Grained Structure in an Al-5.4%Mg-0.5%Mn Alloy Subjected to Severe Plastic Deformation
Ilya Nikulin, Alla Kipelova, Sergey Malopheyev and Rustam Kaibyshev
890-894 :
Low-Cycle Fatigue of Ultrafine-Grained Aluminum at Low Temperatures
Yukito Nakanishi, Toshiyuki Fujii, Susumu Onaka and Masaharu Kato
895-899 :
Kinetics of Hydrogen Desorption from Rapidly Solidified Al-Cr Alloys
Iya I. Tashlykova-Bushkevich, Goroh Itoh, Vasiliy G. Shepelevich and Takahiro Shikagawa
900-905 :
Effects of Microalloying Tin and Combined Addition of Silver and Tin on the Formation of Precipitate Free Zones and Mechanical Properties in Al-Zn-Mg Alloys
Tomo Ogura, Shoichi Hirosawa, Akio Hirose and Tatsuo Sato
906-913 :
Effects of Cu Addition on Behavior of Nanoclusters during Multi-Step Aging in Al-Mg-Si Alloys
JaeHwang Kim, Equo Kobayashi and Tatsuo Sato
914-919 :
Relating Quench Sensitivity to Microstructure in 6000 Series Aluminium Alloys
Katharina Strobel, Mark A. Easton, Lisa Sweet, Malcolm J. Couper and Jian-Feng Nie
920-927 :
Effect of Cooling Rates during Solidification of Al-5.5%Mg-2.3%Si-0.6%Mn and Al-13%Mg2Si Pseudo-Binary Alloys on Their Secondary-Particle Morphology and Tear Toughness
Daisuke Shimosaka, Shinji Kumai, Federico Casarotto and Shuichiro Watanabe
928-933 :
Fluidity and Microstructure Evolution of Al-12%B4C Composites Containing Magnesium
Zhan Zhang, Ken Fortin, Andre Charette and Xiao-Guang Chen
934-938 :
Observation of Foaming Behavior for Rolled Sheet Precursors Made of Various Aluminum Powders
Makoto Kobashi, Masato Noguchi and Naoyuki Kanetake
939-942 :
Preparation of Unidirectional Carbon Fiber Preform for Aluminium Matrix Composites
Moonhee Lee, Yongbum Choi, Kenjiro Sugio, Kazuhiro Matsugi and Gen Sasaki
943-947 :
Effect of Compaction Temperature on Sinterability of Magnesium and Aluminum Powder Mixtures by Warm Compaction Method
Taku Iwaoka and Mitsuru Nakamura
948-952 :
Dissimilar Metal Joining of 2024 and 7075 Aluminium Alloys to Titanium Alloys by Friction Stir Welding
Masayuki Aonuma and Kazuhiro Nakata
953-959 :
Growth Manner of Intermetallic Compound Layer Produced at Welding Interface of Friction Stir Spot Welded Aluminum/Steel Lap Joint
Mitsuhiro Watanabe, Keyan Feng, Yoshio Nakamura and Shinji Kumai
960-966 :
Microstructure and Mechanical Property of 5000 Series Aluminum Stud Joint with Zinc Insert Using Friction Welding
Taichi Nishida, Tomo Ogura, Mitsuo Fujimoto and Akio Hirose
967-973 :
Effects of Zn-Based Alloys Coating on Mechanical Properties and Interfacial Microstructures of Steel/Aluminum Alloy Dissimilar Metals Joints Using Resistance Spot Welding
Keisuke Ueda, Tomo Ogura, Shumpei Nishiuchi, Kenji Miyamoto, Toshikazu Nanbu and Akio Hirose
974-978 :
Interfacial Microstructure and Mechanical Properties of Dissimilar Friction Stir Welds between 6061-T6 Aluminum and Ti-6%Al-4%V Alloys
Ki-Sang Bang, Kwang-Jin Lee, Han-Sur Bang and Hee-Sun Bang
979-984 :
Nanoindentation Measurement of Interfacial Reaction Layers in 6000 Series Aluminum Alloys and Steel Dissimilar Metal Joints with Alloying Elements
Tomo Ogura, Keisuke Ueda, Yuichi Saito and Akio Hirose
985-991 :
Preliminary Investigation of the Microstructure and Mechanical Behaviour of 2024 Aluminium Alloy Friction Spot Welds
Sergio T. Amancio-Filho, Ana P. C. Camillo, Luciano Bergmann, Jorge F. dos Santos, Sebastião E. Kury and Nelson G. A. Machado
992-998 :
Advanced High-Speed Solid-State Joining of 2024 Aluminum Alloy Studs to 5052 Aluminum Alloy Plates
Shinji Kumai, Keisuke Hayashida and Mitsuhiro Watanabe
999-1002 :
Joining of Aluminum to Steel Pipe by Magnetic Pulse Welding
Ji-Yeon Shim, Ill-Soo Kim, Moon-Jin Kang, In-Ju Kim, Kwang-Jin Lee and Bong-Yong Kang
1003-1008 :
Simulation and Experimental Analysis of Metal Jet Emission and Weld Interface Morphology in Impact Welding
Shougo Kakizaki, Mitsuhiro Watanabe and Shinji Kumai
1009-1015 :
Structural Changes of Precipitates by Aging of an Mg-4 at%Dy Solid Solution Studied by Atomic-Scaled Transmission Electron Microscopy
Kaichi Saito, Akira Yasuhara, Masahiko Nishijima and Kenji Hiraga
1016-1025 :
Dislocation Movement in WE43 Magnesium Alloy during Recovery and Recrystallisation
Osvaldo Agustin Lambri, José Angel García, Werner Riehemann, José Angel Cano, Griselda I. Zelada-Lambri and Fernando Plazaola
1026-1032 :
Measurement of Cortical Bone Strain Distribution by Image Correlation Techniques and from Fracture Toughness
Hitoshi Yamaguchi, Hisao Kikugawa, Takashi Asaka, Hirakazu Kasuya and Masahiro Kuninori
1033-1040 :
Applicability of Al-Powder-Alloy Coating to Corrosion Barriers of 316SS in Liquid Lead-Bismuth Eutectic
Yuji Kurata, Hidetomo Sato, Hitoshi Yokota and Tetsuya Suzuki
1041-1047 :
Effect of Aluminum Surface State on Laser Joining between 1050 Aluminum Sheet and Polypropylene Resin Sheet Using Insert Materials
Makoto Hino, Yutaka Mitooka, Koji Murakami, Kazuto Urakami, Hiroyuki Nagase and Teruto Kanadani
1048-1052 :
Synthesis of Palladium Nanoparticles and Palladium/Spherical Carbon Composite Particles in the Solid–Liquid System of Palladium Oxide–Alcohol by Microwave Irradiation
Yoshihiro Sekiguchi, Yamato Hayashi and Hirotsugu Takizawa
1053-1062 :
Prediction of Solidification Paths in Al-Si-Fe Ternary System and Experimental Verification: Part I. Fe-Containing Hypoeutectic Al-Si Alloys
Sanghwan Lee, Bonghwan Kim and Sangmok Lee
1063-1069 :
Nitric Acid Leaching of Base Metals from Waste PDP Electrode Scrap and Recovery of Ruthenium Content from Leached Residues
Jae Woo Ahn, Dong Wha Chung, Ki Woong Lee, Jong-Gwan Ahn and Hong Yong Sohn
1070-1073 :
Enhancement of Grain Refinement and Mechanical Properties of Cross-Roll Rolled Pure Copper
Kuk Hyun Song, Han Sol Kim and Won Yong Kim
1074-1074 :
Errata : Near-Surface Nanocomposite Structure on Commercial Purity Aluminum Induced by Fine Particle Bombardment
Norio Nakamura and Shin-ichi Takagi

[JIM HOME] [JOURNAL ARCHIVES]

© 2011 The Japan Institute of Metals
Comments to us : editjt@jim.or.jp