Materials Transactions Online

Materials Transactions, Vol.51 No.10 (2010)

1719-1719 :
PREFACE
K. Suganuma
1720-1726 :
A Reliability Study of Nanoparticles Reinforced Composite Lead-Free Solder
Si Chen, Lili Zhang, Johan Liu, Yulai Gao and Qijie Zhai
1727-1734 :
Effects of Zn-Bearing Flux on Joint Reliability and Microstructure of Sn-3.5Ag Soldering on Electroless Ni-Au Surface Finish
Hitoshi Sakurai, Youichi Kukimoto, Seongjun Kim, Alongheng Baated, Kiju Lee, Keun-Soo Kim, Seishi Kumamoto and Katsuaki Suganuma
1735-1740 :
Effect of In Addition on Wetting Properties of Sn-Zn-In/Cu Soldering
Yi Ta Wang, Chung Jen Ho and Hsien Lung Tsai
1741-1746 :
Effects of Post-Plating Reflow on Changes in Crystal Grain Size of Sn-2 mass%Bi Alloy Plating with Thermal Cycling Treatment
Noriyuki Kuwano, Atsushi Jinnouchi, Sadanori Horikami, Naruyoshi Hirokado and Harini Sosiati
1747-1752 :
Effect of Small Addition of Zinc on Creep Behavior of Tin
Naoyuki Hamada, Masakazu Hamada, Tokuteru Uesugi, Yorinobu Takigawa and Kenji Higashi
1753-1758 :
Fluxless Bonding of Ni-P/Cu Plated Al Alloy and Cu Alloy with Lead-Free Sn-Cu Foil
Ikuo Shohji, Shinji Koyama, Itaru Oshiro, Hideaki Nara and Yoshiharu Iwata
1759-1763 :
Effect of Formic Acid Surface Modification on Bond Strength of Solid-State Bonded Interface of Tin and Copper
Shinji Koyama, Yukinari Aoki and Ikuo Shohji
1764-1768 :
Synthesis of Highly Concentrated Ag Nanoparticles in a Heterogeneous Solid-Liquid System under Ultrasonic Irradiation
Kenta Toisawa, Yamato Hayashi and Hirotsugu Takizawa
1769-1772 :
Synthesis of Carbon Nanotube/Silver Nanocomposites by Ultrasonication
Takahiro Yamada, Yamato Hayashi and Hirotsugu Takizawa
1773-1778 :
Transmission Electron Microscopy Study on Microstructure of Ag-Based Conductive Adhesives
Naoyuki Kawamoto, Yasukazu Murakami, Daisuke Shindo, Yuichiro Hayasaka, Takeshi Kan and Katsuaki Suganuma
1779-1784 :
Influence of Temperature and Dwelling Time on Low-Cycle Fatigue Characteristic of Isotropic Conductive Adhesive Joint
Yoshiharu Kariya, Yoshihiko Kanda, Keitaro Iguchi and Hiromitsu Furusawa
1785-1789 :
Effects of Silver Coating Covered with Copper Filler on Electrical Resistivity of Electrically Conductive Adhesives
Hiroshi Nishikawa, Saya Mikami, Koichi Miyake, Akira Aoki and Tadashi Takemoto
1790-1795 :
Characteristics of Thermosonic Anisotropic Conductive Adhesives (ACFs) Flip-Chip Bonding
Jong-Min Kim, Yong Song, Minhaeng Cho, Seong Hyuk Lee and Young-Eui Shin
1796-1801 :
Structural Study of Zr50Cu50 Amorphous Alloy by Anomalous X-ray Scattering Coupled with Reverse Monte-Carlo Simulation
T. Kawamata, Y. Yokoyama, M. Saito, K. Sugiyama and Y. Waseda
1802-1808 :
Effect of P Content on Stress Relaxation and Clustering Behavior in Cu-Ni-P Alloys
Yasuhiro Aruga, David W. Saxey, Emmanuelle A. Marquis, Hisao Shishido, Yuya Sumino, Alfred Cerezo and George D. W. Smith
1809-1813 :
Diffusion of Aluminum in β-Titanium
Sung-Yul Lee, Osamu Taguchi and Yoshiaki Iijima
1814-1818 :
Elasto-Plasticity Behavior of High Strength Steel Sheet in Biaxial Stress Path Change
Takeshi Uemori, Tohru Kuramitsu, Yuji Mito, Ryutaro Hino, Tetsuo Naka and Fusahito Yoshida
1819-1824 :
Prediction on Nominal Stress-Strain Curve of Isotropic Polycrystal Ti-15-3-3-3 Sheet by FE Analysis
Long Li, Fuxing Yin and Kotobu Nagai
1825-1832 :
Prediction on Nominal Stress-Strain Curve of Anisotropic Polycrystal with Texture by FE Analysis
Long Li, Kotobu Nagai and Fuxing Yin
1833-1841 :
Effect of Pretreatment Film Composition on Adhesion of Organic Film on Zinc Coated Steel Sheet
Akira Matsuzaki, Masaaki Yamashita and Nobuyoshi Hara
1842-1846 :
Electrodeposition of Silver-Nickel Thin Films with a Galvanostatic Method
Hyeonjin Eom, Byungjun Jeon, Donguk Kim and Bongyoung Yoo
1847-1853 :
Concept of Furnace for Metal Refining by Microwave Heating —A Design of Microwave Smelting Furnace with Low CO2 Emission—
Keiichiro Kashimura, Kazuhiro Nagata and Motoyasu Sato
1854-1860 :
Formation of Internal Crack in High-Speed Twin-Roll Cast 6022 Aluminum Alloy Strip
Min-Seok Kim, Yoshiyuki Arai, Yasuharu Hori and Shinji Kumai
1861-1870 :
Vertical and Horizontal Directional Solidification of Zn-Al and Zn-Ag Diluted Alloys
Sergio F. Gueijman, Carlos E. Schvezov and Alicia E. Ares
1871-1877 :
Pore Morphology of Porous Al-Ti Alloy Fabricated by Continuous Casting in Hydrogen Atmosphere
T. B. Kim, M. Tane, S. Suzuki and H. Nakajima
1878-1882 :
Crystallization Behaviour of Electroless Ni-P UBM with Medium Phosphorous Induced by Single and Step Heat Treatment
Han-Byul Kang, Jongwoo Park, Jee-Hwan Bae and Cheol-Woong Yang
1883-1886 :
Magnetic Properties of Rapidly Solidified Ribbon of Fe49Co49V2 and Spark-Plasma-Sintered Pellet of Its Powder
Minoru Matsumoto, Takeshi Kubota, Masanori Yokoyama, Teiko Okazaki, Yasubumi Furuya, Akihiro Makino and Munekatsu Shimada
1887-1892 :
A New Non-PRM Bumping Process by Electroplating on Si Die for Three Dimensional Packaging
Jiheon Jun, Inrak Kim, Michael Mayer, Y. Norman Zhou, Seungboo Jung and Jaepil Jung
1893-1900 :
Effect of Alumina Content on the Mechanical Properties of Alumina Particle Dispersion Magnesium
Shigehiro Kawamori, Kiyoshi Kuroda, Yukio Kasuga, Masahiro Yokouchi, Hiroshi Fujiwara and Kei Ameyama
1901-1904 :
Influence of Nd Oxide Phase on the Coercivity of Nd-Fe-B Thin Films
Masashi Matsuura, Ryota Goto, Nobuki Tezuka and Satoshi Sugimoto
1905-1908 :
Characteristics of Printed Thin Films Using Indium Tin Oxide (ITO) Ink
Sung-Jei Hong, Jong-Woong Kim, Jae-Won Lim, Good-Sun Choi and Minoru Isshiki
1909-1913 :
Thermoelectric Characteristics of the Thermopile Sensors with Variations of the Width and the Thickness of the Electrodeposited Bismuth-Telluride and Antimony-Telluride Thin Films
Min-Young Kim and Tae-Sung Oh
1914-1918 :
Equal Channel Angular Extrusion Technique for Controlling the Texture of n-Type Bi2Te3 Based Thermoelectric Materials
Takahiro Hayashi, Yuma Horio and Hirotsugu Takizawa
1919-1922 :
Optimization of Sintering Temperature for Maximizing Dimensionless Figure of Merit of La-Doped Strontium Titanate Thermoelectric Material in the Combination of Combustion Synthesis with Post Spark Plasma Sintering
Asami Kikuchi, Lihua Zhang, Noriyuki Okinaka, Tsuyoshi Tosho and Tomohiro Akiyama
1923-1926 :
New Development of Titanium Wire Ball as Vertebra Substitute
Akira Shibata, Yasuhiro Tamagawa, Hiroshi Horikawa, Mitsunobu Iwasaki, Kohji Matsuzaki and Chiaki Hamanishi
1927-1933 :
Recovery of Platinum and Palladium from the Spent Petroleum Catalysts by Substrate Dissolution in Sulfuric Acid
Min-seuk Kim, Eun-young Kim, Jinki Jeong, Jae-chun Lee and Wonbaek Kim
1934-1938 :
Phase Separation from L21 to (B2+L21) in Fe-24.6Al-7.5Ti Alloy
GowDong Tsay, ChunWei Su, YiHsuan Tuan, ChuenGuang Chao and TzengFeng Liu
1939-1943 :
Microstructure Analysis of High Coercivity PLD-Made Nd-Fe-B Thick-Film Improved by Tb-Coating-Diffusion Treatment
Masahiro Ishimaru, Masaru Itakura, Minoru Nishida, Masaki Nakano and Hirotoshi Fukunaga
1944-1950 :
In Vitro Biocompatibility of Ni-Free Ti-Based Shape Memory Alloys for Biomedical Applications
Hiroyasu Kanetaka, Hideki Hosoda, Yoshinaka Shimizu, Tada-aki Kudo, Ye Zhang, Mitsuhiro Kano, Yuya Sano and Shuichi Miyazaki
1951-1957 :
Effect of Oxide Dispersion on Dendritic Grain Growth Characteristics of Cast Aluminum Alloy
Gwang-Ho Kim, Sung-Mo Hong, Min-Ku Lee, Soon-Ho Kim, Ikuo Ioka, Byoung-Suhk Kim and Ick-Soo Kim
1958-1963 :
Microstructures and the Charge-Discharge Characteristics of Advanced Al-Si Thin Film Materials
Chao-Han Wu, Fei-Yi Hung, Truan-Sheng Lui and Li-Hui Chen
1964-1972 :
Numerical Study of Fluid Flow and Heat Transfer Behaviors in a Physical Model Similar in Shape to an Actual Glass Melting Furnace and Its Experimental Verification
Chien-Chih Yen and Weng-Sing Hwang
1973-1976 :
Effect of Denucleating Techniques on Undercooling of Co2NiGa Alloys
Li Junzheng, Liu Jian, Zhang Yongjun and Li Jianguo
1977-1980 :
Simulation of Deposition Behavior of Bulk Amorphous Particles in Cold Spraying
Xianglin Zhou, Xiangkun Wu, Saijie Mou, Jingchun Liu and Jishan Zhang

[JIM HOME] [JOURNAL ARCHIVES]

© 2010 The Japan Institute of Metals
Comments to us : editjt@jim.or.jp