Materials Transactions Online

Materials Transactions, Vol.49 No.5 (2008)

893-893 :
PREFACE
Kenji Higashi, Shigeharu Kamado, Yoshihito Kawamura
894-897 :
Recent Development and Applications of Magnesium Alloys in the Hyundai and Kia Motors Corporation
Jae Joong Kim and Do Suck Han
898-902 :
Suppression of Macroscopic Defects through the Control of Friction between Workpiece and Dies in a Forged Magnesium Alloy Part with Ribs
Akira Takara, Li-Fu Chian, Sung Wook Chung, Hidetoshi Somekawa, Hiroyuki Watanabe, Yorinobu Takigawa and Kenji Higashi
[Erratum]
903-908 :
Effect of Environmentally Friendly Anodization on the Mechanical Properties and Microstructure of AZ91D Magnesium Alloy
Atsushi Saijo, Koji Murakami, Makoto Hino and Teruto Kanadani
909-912 :
Clarification of the Necessary Value of Surface Roughness for Developing Luster on an AZ31 Magnesium Alloy Surface with or without Acid Aqueous Solution Treatment
Miyoshi Ohara, Haruo Okahara, Yorinobu Takigawa and Kenji Higashi
913-917 :
Effects of 2 mass% Li Addition on the AZ80 Mg Alloy
P. C. Wang, C. C. Lin, T. Y. Huang, H. C. Lin, Y. H. Lee, M. T. Yeh and J. Y. Wang
918-923 :
Microalloying Effects of Ca and Ni on High-Temperature Creep Behavior in Mg-Y-Zn Alloys
Mayumi Suzuki, Kayo Tsuchida and Kouichi Maruyama
924-930 :
Effects of Alloying Elements on Characteristics of Anodic Oxidized Coatings in Various Mg-Al-Zn Series Alloys
Makoto Hino, Koji Murakami, Atsushi Saijo and Teruto Kanadani
931-935 :
Influence of Zn Addition on Aging Response and Corrosion Resistance of Mg-Gd-Nd-Zr Alloy
B. K. Park, J. H. Jun and J. M. Kim
936-940 :
Effect of Sb and Sr Additions on the Microstructural Evolution of Mg-Sn-Al-Si Based Alloys
D. H. Kang, G. T. Bae and Nack J. Kim
941-944 :
Effects of Zn/Gd Ratio and Content of Zn, Gd on Phase Constitutions of Mg Alloys
Yong Liu, Guangyin Yuan, Song Zhang, Xinping Zhang, Chen Lu and Wenjiang Ding
945-951 :
The Effects of Yttrium Element on Microstructure and Mechanical Properties of Mg-5 mass%Al-3 mass%Ca Based Alloys Fabricated by Gravity Casting and Extrusion Process
Hyeon-Taek Son, Jae-Seol Lee, Chang-Seog Kang, Jung-Chan Bae, Kyosuke Yoshimi and Kouichi Maruyama
952-956 :
Effect of Rare-Earth Elements Y and Dy on the Deformation Behavior of Mg Alloy Single Crystals
Seiji Miura, Shigeki Imagawa, Takeshi Toyoda, Kenji Ohkubo and Tetsuo Mohri
957-962 :
Effect of Solution Treatment on Microstructure Evolution and Mechanical Properties of Mg-6.0Zn-0.6Y-0.5Zr Alloy Processed by Equal Channel Angular Extrusion
Weineng Tang, Rongshi Chen and Enhou Han
963-966 :
Comparison in Deformation and Fracture Behavior of Magnesium during Equal Channel Angular Pressing by Experimental and Numerical Methods
Seung Chae Yoon, Cheon Hee Bok, Min Hong Seo, Taek-Soo Kim and Hyoung Seop Kim
967-971 :
Yield and Densification Behavior of Rapidly Solidified Magnesium Powders
Seung Chae Yoon, Eun Jeong Kwak, Taek-Soo Kim, Byeong Sun Cheon and Hyoung Seop Kim
972-975 :
Effect of Ultrasonic Vibration Pretreatment on Microstructural Evolution and Mechanical Properties of Extruded AZ91 Alloy
Yoshiaki Osawa, Xinbao Liu, Susumu Takamori, Hidetoshi Somekawa and Toshiji Mukai
976-979 :
Effect of CaO on AZ31 Mg Strip Castings
Dong-In Jang, Young-Ok Yoon, Seung-Boo Jung and Shae K. Kim
980-985 :
Mechanical Properties and Microstructure of Twin-Roll Cast Mg-Zn-Y Alloy
Kyung-Hun Kim, Jung Gu Lee, Geun Tae Bae, Jun Ho Bae and Nack J. Kim
986-989 :
Optimization of Heat Treatment in AZ64 Magnesium Alloy
Songmao Liang, Yuequn Ma, Rongshi Chen and Enhou Han
990-994 :
Microstructure Evolutions of Rapidly-Solidified and Conventionally-Cast Mg97Zn1Y2 Alloys
Akira Ono, Eiji Abe, Takaomi Itoi, Mitsuji Hirohashi, Michiaki Yamasaki and Yoshihito Kawamura
995-999 :
Effects of Wavy Roll-Forming on Textures in AZ31B Magnesium Alloy
A. Yamamoto, Y. Tsukahara and S. Fukumoto
1000-1005 :
Improvement of Forgeability of a Commercial AZ31B Magnesium Alloy in Cold Backward Extrusion with Counter Pressure
Ryo Matsumoto, Tomoo Kubo and Kozo Osakada
1006-1010 :
Processing and Mechanical Properties of Fine Grained Magnesium by Equal Channel Angular Pressing
Eun Jeong Kwak, Cheon Hee Bok, Min Hong Seo, Taek-Soo Kim and Hyoung Seop Kim
1011-1014 :
The Influence of Developed Texture on the Mechanical Anisotropy and Deformation Modes of an As-Extruded Mg-Zn-Zr Alloy
D. K. Xu, L. Liu, Y. B. Xu and E. H. Han
1015-1020 :
Evolution of Ultra-Fine Grains in AZ31 and AZ61 Mg Alloys during Multi Directional Forging and Their Properties
H. Miura, X. Yang and T. Sakai
1021-1024 :
Effect of the Cyclic Extrusion and Compression Processing on Microstructure and Mechanical Properties of As-Extruded ZK60 Magnesium Alloy
Jinbao Lin, Qudong Wang, Liming Peng and Tao Peng
1025-1031 :
Microstructure and Mechanical Properties of Mg-Al-Ca-Nd Alloys Fabricated by Gravity Casting and Extrusion Process
Hyeon-Taek Son, Jae-Seol Lee, Ik-Hyun Oh, Dae-Guen Kim, Kyosuke Yoshimi and Kouichi Maruyama
1032-1037 :
Effects of Homogenization Annealing on Dynamic Recrystallization in Mg-Al-Ca-RE (Rare Earth) Alloy
Masataka Hakamada, Akira Watazu, Naobumi Saito and Hajime Iwasaki
1038-1041 :
Production of Alumina-Rich Surface Film on AZ31 Magnesium Alloy by Anodizing with Co-Precipitation of Nano-Sized Alumina
S. A. Salman, R. Ichino and M. Okido
1042-1047 :
Microstructures and Corrosion Properties on Fluoride Treated Magnesium Alloy
A. Yamamoto, T. Terawaki and H. Tsubakino
1048-1051 :
Surface Protection Effect of Diffusion Pack Cementation Process by Al-Si Powders with Chloride Activator on Magnesium and Its Alloys
Joon Sik Park, Jeong Min Kim, Ha Young Kim, Jae Seol Lee, Ik Hyun Oh and Chang Suck Kang
1052-1056 :
Investigation of Stress Corrosion Cracking Behaviors of an AZ91 Magnesium Alloy in 0.1 kmol/m3 Na2SO4 Solution Using Slow Strain Rate Test
Jianqiu Wang, Jian Chen, Enhou Han and Wei Ke
1057-1064 :
Mechanism of Corrosion Protection of Anodized Magnesium Alloys
Koji Murakami, Makoto Hino, Kiyomichi Nakai, Sengo Kobayashi, Atsushi Saijo and Teruto Kanadani
1065-1070 :
Influence of Conversion Coating on Magnesium and Aluminum Alloys by Adhesion Method
Manabu Takai and Matsufumi Takaya
1071-1076 :
Improvement of Corrosion Resistance of Magnesium Alloys by Surface Film with Rare Earth Element
Toshihide Takenaka, Yuji Narazaki, Nobuo Uesaka and Masahiro Kawakami
1077-1080 :
Influence of Ga Content on Electrochemical Behavior of Mg-5 at%Hg Anode Materials
Yan Feng, R-Chu Wang, Kun Yu, C-Qun Peng and W-Xian Li
1081-1083 :
Effect of CaO on Oxidation Resistance and Microstructure of Pure Mg
Seong-Ho Ha, Jin-Kyu Lee and Shae K. Kim
1084-1088 :
Effect of Ca and CaO on the High Temperature Oxidation of AZ91D Mg Alloys
Dong-Bok Lee, Lee-Seok Hong and Young-Jig Kim
1089-1092 :
Casting Surface of AZ91 Alloy and Its Reaction with Sand Mold
Susumu Takamori, Yoshiaki Osawa, Takashi Kimura, Xinbao Liu and Toshiji Mukai
1093-1100 :
Deformation Characteristics of Recycled AZ91 Mg Alloy Containing Oxide Contaminants
Yasumasa Chino and Mamoru Mabuchi
1101-1106 :
Experimentally and Numerical Study on Deep Drawing Process for Magnesium Alloy Sheet at Elevated Temperatures
D. V. Hai, S. Itoh, T. Sakai, S. Kamado and Y. Kojima
1107-1111 :
Analysis of Strain Transfer through the Mg/Ti Interface Using Crystallographic Orientation Analysis Based on Electron Back-Scattered Diffraction Patterns
Hiroaki Kawamoto, Seiji Miura, Kaori Yano, Kenji Ohkubo and Tetsuo Mohri
1112-1119 :
Experimental Determination of Forming Limit Diagram and Springback Characteristics of AZ31B Mg Alloy Sheets at Elevated Temperatures
Hyung Jong Kim, Sun Chul Choi, Kyoung Taek Lee and Heon Young Kim
1120-1123 :
Non-Isothermal Simulation of Warm Circular Cup Deep Drawing Processing of an AZ31 Magnesium Alloy Sheet
Myeong Han Lee, Heon Young Kim, Heung Kyu Kim, Gi Deuck Kim and Soo Ik Oh
1124-1128 :
Simultaneous Control of Shape and Properties of AZ31 Magnesium Alloy Sheets by Incremental Forming
Masaaki Otsu, Yusuke Kai and Kazuki Takashima
1129-1131 :
Dissimilar Welding of Al and Mg Alloys by FSW
Taiki Morishige, Atsushi Kawaguchi, Masato Tsujikawa, Makoto Hino, Tomotake Hirata and Kenji Higashi
1132-1136 :
Butt Joining of Magnesium Alloy Sheet by Shot Peening
Yasunori Harada, Makoto Fukunaga and Atsushi Yamamoto
1137-1141 :
Some Characteristics of AZ31/AZ91 Dissimilar Magnesium Alloy Deposit by Friction Surfacing
Dai Nakama, Kazuyoshi Katoh and Hiroshi Tokisue
1142-1147 :
Analysis of Explosively Welded Aluminum–AZ31 Magnesium Alloy Joints
Seyed Hadi Ghaderi, Akihisa Mori and Kazuyuki Hokamoto
1148-1156 :
High Cycle Fatigue Property of Extruded Non-Combustible Mg Alloy AMCa602
Kiyotaka Masaki, Yasuo Ochi, Toshifumi Kakiuchi, Keiichi Kurata, Toru Hirasawa, Takashi Matsumura, Yorinobu Takigawa and Kenji Higashi
1157-1161 :
Relationship between Fatigue Strength and Grain Size in AZ31 Magnesium Alloys
Masayuki Tsushida, Kei Shikada, Hiromoto Kitahara, Shinji Ando and Hideki Tonda
1162-1167 :
Shaping of Helical Gear by Two-Step Cold Extrusion
Hajime Yoshida, Yozo Sawaki and Yoshihisa Sakaida
1168-1174 :
Pseudo-HIP Combustion Synthesis of FeAl-TiB2 Composites
Yuki Obara, Masayuki Kudoh and Kiyotaka Matsuura
1175-1179 :
Effect of Specimen Size and Aging on Tensile Properties of Sn-Ag-Cu Lead-Free Solders
Ikuo Shohji, Tsutomu Osawa, Takashige Matsuki, Yoshiharu Kariya, Kiyokazu Yasuda and Tadashi Takemoto
1180-1185 :
Effects of Glass Transition Temperatures of Films on the Corrosion Resistance after Forming of Pre-Coated Aluminum Sheets
Nobuo Hattori, Masaki Tanigawa and Masazumi Okido
1186-1191 :
Effects of Mg Additions on Microstructure and Optical Properties of Sol-Gel Derived ZnO Thin Films
Chien-Yie Tsay, Min-Chi Wang and Shin-Chuan Chiang
1192-1198 :
Kinetics of Oxidative Roasting of Complex Copper Concentrate
Byung-Su Kim, Eun-young Kim, Chi-Kwon Kim, Hoo-In Lee and Jeong-Soo Sohn
1199-1201 :
Mechanical Characteristics of Center Bevelled Double Structure Blade
Darulihsan Abdul Hamid, Shigeru Nagasawa, Yasushi Fukuzawa, Kiyoshi Kojima and Akira Hine

[JIM HOME] [JOURNAL ARCHIVES]

© 2008 The Japan Institute of Metals
Comments to us : editjt@jim.or.jp